Shenzhen Meiyuxin Technology Co., Ltd. [supply electronic components FBGA] imported original LFD2NX-17-8MG121C FPGA - Field Programmable Gate Array Lattice Certus-NX General Purpose FPGA on Nexus platform (28nm FD-SOI)! ! !

Product Description:

LFD2NX-17-8MG121CThe Certus™-NX family of low-power general-purpose FPGAs can be used in a broad range of applications across multiple markets and are optimized for bridging processing needs in edge applications. It is built on the Lattice Nexus™ FPGA platform using low power 28nm FD-SOI technology. It combines the extreme reliability of FD-SOI (due to extremely low SER) technology with low power consumption and high FPGA flexibility, and offers small form factor packaging options with a large number of I/Os per square millimeter. Design security AES-256 encryption and Features such as ECDSA also support authentication. Certus-NX supports a variety of interfaces including PCIExpress (Gen1, Gen2), SGMII (Gigabit Ethernet), LVDS, LVCMOS (0.9–3.3 V), and more.

LFD2NX-17-8MG121C The processing capabilities of Certus-NX include up to 39k logic cells, 56 multipliers (18 × 18), 2.9 Mb embedded memory (blocked by EBR and LRAM), distributed memory, DRAM interface (supports DDR3, DDR3L, LPDDR2 and LPDDR3 up to 1066 Mbps × 16-bit data width). Certus-NX FPGAs support fast configuration reconfigurable SRAM-based logic fabrics, and ultra-fast programmable configuration (less than 3 milliseconds) System I/O™. In addition to the inherently high reliability of FD-SOI technology (due to its extremely low SER), active reliability features such as built-in frame-based SED/SEC (for SRAM-based logic structures) and ECC (for EBR and LRAM). Dual 12-bit ADCs are available for on-chip system monitoring functions.

Lattice Radiant™ design software allows large and complex user designs on the Certus-NX FPGA family. Synthesis library support for Certus-NX devices is available for popular logic synthesis tools. Radiation tools use compositing tools

The output and constraints of the floor plan tool place and route user-designed devices for Certus-NX.

LFD2NX-17-8MG121C These tools extract timing from routing and back-inject it into the design for timing verification. Lattice offers a number of pre-designed IP (Intellectual properties) modules for the Certus-NX family. By using these configurable soft IP cores as standardized blocks, you are free to focus on unique aspects of your design, increasing your productivity.

Features

 Programmable architecture

 17 k to 39 k logic cells

 24 to 56 sysDSP™ blocks (18 x 18 multipliers)

 2.5 to 2.9 Mb of embedded memory (EBR, LRAM)

 78 to 192 programmable sysI/O (High Performance and Wide Range I/O)

 Programmable sysI/O supports wide variety of interfaces

 High Performance (HP) I/O on bottom I/Obanks

 Supports up to 1.8 V VCCIO

 Mixed voltage support (1.0 V, 1.2 V, 1.5 V, 1.8V)

 High-speed differential up to 1.5 Gbps

 Supports LVDS, Soft D-PHY (Tx/Rx), LVDS 7:1(Tx/Rx), SLVS (Tx/Rx), subLVDS (Rx)

 Supports SGMII (Gb Ethernet)

 Two channels (Tx/Rx) at 1.25 Gbps

 Dedicated DDR3/DDR3L and LPDDR2/LPDDR3  memory support with DQS logic, up to 1066 Mbps data rate and x16 bits data width

 Wide Range (WR) I/O on left, right, and top I/O Banks

 Supports up to 3.3 V VCCIO

 Mixed voltage support (1.2 V, 1.5 V, 1.8 V, 2.5 V, 3.3 V)

 Programmable slew rate (slow, med, fast)

 Controlled impedance mode

 Emulated LVDS support

 Hot Socketing Support

 Power modes – Low Power, High-Performance

 User selectable

 Low-Power mode for power and/or thermal challenges

 High-Performance mode for faster processing

 Small footprint package options

 6 mm × 6 mm package option in both densities